From 0db1b11073af0282282e3c825a0498c19c837383 Mon Sep 17 00:00:00 2001 From: Christoph Krapp Date: Sat, 8 Nov 2025 22:47:07 +0100 Subject: [PATCH] ipq40xx: add support for Netgear RBS20 This device has only half the flash and ram of the RBR20. It also has two lan ports instead of wan and lan. Hardware -------- SOC: Qualcomm IPQ4019 FLASH: 128MB (Winbond W29N01HVSINF) RAM: 256MB (Winbond W632GU6MB-12) WIFI: Qualcomm IPQ4019 Qualcomm Atheros QCA9886 ETH: 2x LAN LED: 5 (4 RGB at top, 1 RG at back) BTN: WPS, Reset UART: 115200 8N1 (dotted Pin = VCC) VCC-TX-RX-GND MAC addresses ------------- LAN Label MAC (stored in boarddata1 offset 0x0) 2.4G LAN 5GLow LAN + 3 (stored in boarddata1 offset 0xc) 5GUpper LAN + 2 (stored in boarddata1 offset 0x12) Installation ------------ Either use the vendor ui upgrade method or nmrpflash to install the factory image. Signed-off-by: Christoph Krapp Link: https://github.com/openwrt/openwrt/pull/20560 Signed-off-by: Robert Marko --- .../uboot-tools/uboot-envtools/files/ipq40xx | 3 +- .../ipq40xx/base-files/etc/board.d/02_network | 3 +- .../base-files/lib/upgrade/platform.sh | 1 + .../arm/boot/dts/qcom/qcom-ipq4019-rbr20.dts | 267 +---------------- .../arm/boot/dts/qcom/qcom-ipq4019-rbs20.dts | 210 ++++++++++++++ .../arm/boot/dts/qcom/qcom-ipq4019-rbx20.dtsi | 270 ++++++++++++++++++ target/linux/ipq40xx/image/generic.mk | 20 +- 7 files changed, 502 insertions(+), 272 deletions(-) create mode 100644 target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbs20.dts create mode 100644 target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbx20.dtsi diff --git a/package/boot/uboot-tools/uboot-envtools/files/ipq40xx b/package/boot/uboot-tools/uboot-envtools/files/ipq40xx index b3d18980d5..e2d67d7f19 100644 --- a/package/boot/uboot-tools/uboot-envtools/files/ipq40xx +++ b/package/boot/uboot-tools/uboot-envtools/files/ipq40xx @@ -55,7 +55,8 @@ aruba,ap-365) ;; buffalo,wtr-m2133hp|\ netgear,lbr20|\ -netgear,rbr20) +netgear,rbr20|\ +netgear,rbs20) ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x40000" "0x20000" ;; linksys,ea6350v3) diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 737fcee083..13b1cdc43a 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -81,7 +81,8 @@ ipq40xx_setup_interfaces() ;; avm,fritzrepeater-3000|\ cellc,rtl30vw|\ - compex,wpj428) + compex,wpj428|\ + netgear,rbs20) ucidef_set_interface_lan "lan1 lan2" ;; devolo,magic-2-wifi-next) diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 248832d467..21ec2f4d29 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -124,6 +124,7 @@ platform_do_upgrade() { mobipromo,cm520-79f|\ netgear,lbr20|\ netgear,rbr20|\ + netgear,rbs20|\ netgear,wac510|\ p2w,r619ac-64m|\ p2w,r619ac-128m|\ diff --git a/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbr20.dts b/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbr20.dts index 269be9fdfb..bc713e0759 100644 --- a/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbr20.dts +++ b/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbr20.dts @@ -1,178 +1,10 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include "qcom-ipq4019.dtsi" -#include -#include -#include -#include +#include "qcom-ipq4019-rbx20.dtsi" / { model = "Netgear RBR20"; compatible = "netgear,rbr20"; - - chosen { - bootargs-append = "ubi.mtd=ubi root=/dev/ubiblock0_0"; - }; - - aliases { - led-boot = &led_status_white; - led-failsafe = &led_status_red; - led-running = &led_status_green; - led-upgrade = &led_status_blue; - label-mac-device = &gmac; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - - led-0 { - function = LED_FUNCTION_POWER; - color = ; - gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - - led-1 { - function = LED_FUNCTION_POWER; - color = ; - gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>; - panic-indicator; - }; - - led_status_green: led-2 { - function = LED_FUNCTION_STATUS; - color = ; - gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>; - }; - - led_status_red: led-3 { - function = LED_FUNCTION_STATUS; - color = ; - gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>; - }; - - led_status_blue: led-4 { - function = LED_FUNCTION_STATUS; - color = ; - gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>; - }; - - led_status_white: led-5 { - function = LED_FUNCTION_STATUS; - color = ; - gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>; - }; - }; - - soc { - tcsr@1949000 { - compatible = "qcom,tcsr"; - reg = <0x1949000 0x100>; - qcom,wifi_glb_cfg = ; - }; - - tcsr@194b000 { - status = "okay"; - - compatible = "qcom,tcsr"; - reg = <0x194b000 0x100>; - qcom,usb-hsphy-mode-select = ; - }; - - ess_tcsr@1953000 { - compatible = "qcom,tcsr"; - reg = <0x1953000 0x1000>; - qcom,ess-interface-select = ; - }; - - tcsr@1957000 { - compatible = "qcom,tcsr"; - reg = <0x1957000 0x100>; - qcom,wifi_noc_memtype_m0_m2 = ; - }; - }; -}; - -&prng { - status = "okay"; -}; - -&mdio { - status = "okay"; - pinctrl-0 = <&mdio_pins>; - pinctrl-names = "default"; -}; - -&crypto { - status = "okay"; -}; - -&watchdog { - status = "okay"; -}; - -&blsp_dma { - status = "okay"; -}; - -&qpic_bam { - status = "okay"; -}; - -&tlmm { - mdio_pins: mdio-pinmux { - mux_mdio { - pins = "gpio6"; - function = "mdio"; - bias-pull-up; - }; - - mux_mdc { - pins = "gpio7"; - function = "mdc"; - bias-pull-up; - }; - }; - - serial_pins: serial-pinmux { - function = "blsp_uart0"; - pins = "gpio16", "gpio17"; - bias-disable; - }; - - nand_pins: nand-pins { - pullups { - pins = "gpio53", "gpio58", "gpio59"; - function = "qpic"; - bias-pull-up; - }; - - pulldowns { - pins = "gpio54", "gpio55", "gpio56", - "gpio57", "gpio60", "gpio61", - "gpio62", "gpio63", "gpio64", - "gpio65", "gpio66", "gpio67", - "gpio68", "gpio69"; - function = "qpic"; - bias-pull-down; - }; - }; }; &nand { @@ -377,70 +209,6 @@ }; }; -&blsp1_i2c3 { - status = "okay"; - - led-controller@27 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "ti,tlc59108"; /* really is tlc59208f */ - reg = <0x27>; - - led0@0 { - function = LED_FUNCTION_BACKLIGHT; - function-enumerator = <0>; - color = ; - reg = <0x0>; - linux,default-trigger = "default-on"; - }; - - led1@1 { - function = LED_FUNCTION_BACKLIGHT; - function-enumerator = <1>; - color = ; - reg = <0x1>; - linux,default-trigger = "default-on"; - }; - - led2@2 { - function = LED_FUNCTION_BACKLIGHT; - function-enumerator = <2>; - color = ; - reg = <0x2>; - linux,default-trigger = "default-on"; - }; - - led3@3 { - function = LED_FUNCTION_BACKLIGHT; - function-enumerator = <3>; - color = ; - reg = <0x3>; - linux,default-trigger = "default-on"; - }; - }; -}; - -&blsp1_uart1 { - status = "okay"; - pinctrl-0 = <&serial_pins>; - pinctrl-names = "default"; -}; - -&cryptobam { - status = "okay"; -}; - -&gmac { - status = "okay"; - - nvmem-cell-names = "mac-address"; - nvmem-cells = <&mac_address_lan 0>; -}; - -&switch { - status = "okay"; -}; - &swport4 { status = "okay"; @@ -454,36 +222,3 @@ label = "lan"; }; - -&pcie0 { - status = "okay"; - - perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; - wake-gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; -}; - -&pcie_bridge0 { - wifi@0,0 { - compatible = "qcom,ath10k"; - reg = <0x00010000 0 0 0 0>; - ieee80211-freq-limit = <5170000 5350000>; - nvmem-cell-names = "pre-calibration", "mac-address"; - nvmem-cells = <&precal_art_9000>, <&mac_address_wlan_2nd5g 0>; - qcom,ath10k-calibration-variant = "Netgear-RBK20"; - }; -}; - -&wifi0 { - status = "okay"; - nvmem-cell-names = "pre-calibration", "mac-address"; - nvmem-cells = <&precal_art_1000>, <&mac_address_lan 0>; - qcom,ath10k-calibration-variant = "Netgear-RBK20"; -}; - -&wifi1 { - status = "okay"; - ieee80211-freq-limit = <5470000 5815000>; - nvmem-cell-names = "pre-calibration", "mac-address"; - nvmem-cells = <&precal_art_5000>, <&mac_address_wlan_5g 0>; - qcom,ath10k-calibration-variant = "Netgear-RBK20"; -}; diff --git a/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbs20.dts b/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbs20.dts new file mode 100644 index 0000000000..c35a9139aa --- /dev/null +++ b/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbs20.dts @@ -0,0 +1,210 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019-rbx20.dtsi" + +/ { + model = "Netgear RBS20"; + compatible = "netgear,rbs20"; +}; + +&nand { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x00000000 0x00100000>; + read-only; + }; + + partition@100000 { + label = "0:MIBIB"; + reg = <0x00100000 0x00100000>; + read-only; + }; + + partition@200000 { + label = "0:BOOTCONFIG"; + reg = <0x00200000 0x00100000>; + read-only; + }; + + partition@300000 { + label = "0:QSEE"; + reg = <0x00300000 0x00100000>; + read-only; + }; + + partition@400000 { + label = "0:QSEE_1"; + reg = <0x00400000 0x00100000>; + read-only; + }; + + partition@500000 { + label = "0:CDT"; + reg = <0x00500000 0x00080000>; + read-only; + }; + + partition@580000 { + label = "0:CDT_1"; + reg = <0x00580000 0x00080000>; + read-only; + }; + + partition@600000 { + label = "0:BOOTCONFIG1"; + reg = <0x00600000 0x00080000>; + read-only; + }; + + partition@680000 { + label = "0:APPSBLENV"; + reg = <0x00680000 0x00080000>; + }; + + partition@700000 { + label = "0:APPSBL"; + reg = <0x00700000 0x00200000>; + read-only; + }; + + partition@900000 { + label = "0:APPSBL_1"; + reg = <0x00900000 0x00200000>; + read-only; + }; + + partition@b00000 { + label = "0:ART"; + reg = <0x00b00000 0x00080000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + precal_art_1000: precal@1000 { + reg = <0x1000 0x2f20>; + }; + + precal_art_5000: precal@5000 { + reg = <0x5000 0x2f20>; + }; + + precal_art_9000: precal@9000 { + reg = <0x9000 0x2f20>; + }; + }; + }; + + partition@b80000 { + label = "0:ART.bak"; + reg = <0x00b80000 0x00080000>; + read-only; + }; + + partition@c00000 { + label = "config"; + reg = <0x00c00000 0x00100000>; + read-only; + }; + + partition@d00000 { + label = "boarddata1"; + reg = <0x00d00000 0x00080000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + mac_address_lan: macaddr@0 { + compatible = "mac-base"; + reg = <0x0 0x6>; + #nvmem-cell-cells = <1>; + }; + + mac_address_wlan_5g: macaddr@c { + compatible = "mac-base"; + reg = <0xc 0x6>; + #nvmem-cell-cells = <1>; + }; + + mac_address_wlan_2nd5g: macaddr@12 { + compatible = "mac-base"; + reg = <0x12 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@d80000 { + label = "boarddata2"; + reg = <0x00d80000 0x00040000>; + read-only; + }; + + partition@dc0000 { + label = "pot"; + reg = <0x00dc0000 0x00100000>; + read-only; + }; + + partition@ec0000 { + label = "boarddata1.bak"; + reg = <0x00ec0000 0x00080000>; + read-only; + }; + + partition@f40000 { + label = "boarddata2.bak"; + reg = <0x00f40000 0x00040000>; + read-only; + }; + + partition@f80000 { + label = "language"; + reg = <0x00f80000 0x00300000>; + read-only; + }; + + partition@1280000 { + label = "ntgrdata"; + reg = <0x01280000 0x01e00000>; + }; + + partition@3080000 { + label = "kernel"; + reg = <0x03080000 0x00700000>; + }; + + partition@3780000 { + label = "ubi"; + reg = <0x03780000 0x04880000>; + }; + }; + }; +}; + +&swport4 { + status = "okay"; + + label = "lan1"; +}; + +&swport5 { + status = "okay"; + + label = "lan2"; +}; diff --git a/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbx20.dtsi b/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbx20.dtsi new file mode 100644 index 0000000000..08d2c0e4a0 --- /dev/null +++ b/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbx20.dtsi @@ -0,0 +1,270 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include +#include + +/ { + chosen { + bootargs-append = "ubi.mtd=ubi root=/dev/ubiblock0_0"; + }; + + aliases { + led-boot = &led_status_white; + led-failsafe = &led_status_red; + led-running = &led_status_green; + led-upgrade = &led_status_blue; + label-mac-device = &gmac; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + function = LED_FUNCTION_POWER; + color = ; + gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led-1 { + function = LED_FUNCTION_POWER; + color = ; + gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + + led_status_green: led-2 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>; + }; + + led_status_red: led-3 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>; + }; + + led_status_blue: led-4 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>; + }; + + led_status_white: led-5 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>; + }; + }; + + soc { + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + status = "okay"; + + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + }; +}; + +&prng { + status = "okay"; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; +}; + +&crypto { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio-pinmux { + mux_mdio { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + + mux_mdc { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_pins: serial-pinmux { + function = "blsp_uart0"; + pins = "gpio16", "gpio17"; + bias-disable; + }; + + nand_pins: nand-pins { + pullups { + pins = "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", + "gpio57", "gpio60", "gpio61", + "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", + "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; +}; + +&blsp1_i2c3 { + status = "okay"; + + led-controller@27 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,tlc59108"; /* really is tlc59208f */ + reg = <0x27>; + + led0@0 { + function = LED_FUNCTION_BACKLIGHT; + function-enumerator = <0>; + color = ; + reg = <0x0>; + linux,default-trigger = "default-on"; + }; + + led1@1 { + function = LED_FUNCTION_BACKLIGHT; + function-enumerator = <1>; + color = ; + reg = <0x1>; + linux,default-trigger = "default-on"; + }; + + led2@2 { + function = LED_FUNCTION_BACKLIGHT; + function-enumerator = <2>; + color = ; + reg = <0x2>; + linux,default-trigger = "default-on"; + }; + + led3@3 { + function = LED_FUNCTION_BACKLIGHT; + function-enumerator = <3>; + color = ; + reg = <0x3>; + linux,default-trigger = "default-on"; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac { + status = "okay"; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&mac_address_lan 0>; +}; + +&switch { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + + perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; +}; + +&pcie_bridge0 { + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + ieee80211-freq-limit = <5170000 5350000>; + nvmem-cell-names = "pre-calibration", "mac-address"; + nvmem-cells = <&precal_art_9000>, <&mac_address_wlan_2nd5g 0>; + qcom,ath10k-calibration-variant = "Netgear-RBK20"; + }; +}; + +&wifi0 { + status = "okay"; + nvmem-cell-names = "pre-calibration", "mac-address"; + nvmem-cells = <&precal_art_1000>, <&mac_address_lan 0>; + qcom,ath10k-calibration-variant = "Netgear-RBK20"; +}; + +&wifi1 { + status = "okay"; + ieee80211-freq-limit = <5470000 5815000>; + nvmem-cell-names = "pre-calibration", "mac-address"; + nvmem-cells = <&precal_art_5000>, <&mac_address_wlan_5g 0>; + qcom,ath10k-calibration-variant = "Netgear-RBK20"; +}; diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index af637c4ba3..544fe0424d 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -911,13 +911,10 @@ define Device/netgear_lbr20 endef TARGET_DEVICES += netgear_lbr20 -define Device/netgear_rbr20 +define Device/netgear_rbx20 $(call Device/DniImage) SOC := qcom-ipq4019 DEVICE_VENDOR := NETGEAR - DEVICE_MODEL := RBR20 - NETGEAR_BOARD_ID := RBR20 - NETGEAR_HW_ID := 29765641+0+256+512+2x2+2x2+2x2 KERNEL_SIZE := 7340032 BLOCKSIZE := 128k PAGESIZE := 2048 @@ -930,8 +927,23 @@ define Device/netgear_rbr20 append-metadata DEVICE_PACKAGES := ipq-wifi-netgear_rbk20 ath10k-firmware-qca9888-ct endef + +define Device/netgear_rbr20 + $(call Device/netgear_rbx20) + DEVICE_MODEL := RBR20 + NETGEAR_BOARD_ID := RBR20 + NETGEAR_HW_ID := 29765641+0+256+512+2x2+2x2+2x2 +endef TARGET_DEVICES += netgear_rbr20 +define Device/netgear_rbs20 + $(call Device/netgear_rbx20) + DEVICE_MODEL := RBS20 + NETGEAR_BOARD_ID := RBS20 + NETGEAR_HW_ID := 29765641+0+128+512+2x2+2x2+2x2 +endef +TARGET_DEVICES += netgear_rbs20 + define Device/netgear_rbx40 $(call Device/netgear_orbi) NETGEAR_HW_ID := 29765515+0+4096+512+2x2+2x2+2x2 -- 2.30.2